Stamping Scrabble Tile Tutorial

9:09 PM Posted In , , , , , , , , , , , Edit This 0 Comments »
crabble tile pendants certainly are all the rage at the moment, but there's no reason to settle for the typical cut and paste projects. This tutorial will walk you through using fun stamps, Pearl Ex Pigments and micro beads to create some one-of-a-kind pendants and charms of your own.






(A view of my chaotic work space at home:)


Ingredients:
  • Scrabble tiles or similar (there are some scrabble tile look-a-likes out there)
  • A variety of stamps - smaller stamps will fit the scrabble tiles, but remember that you can use just a part of a larger stamp for an interesting affect
  • Ink pads in a variety of colors - I reccomend Staz On
  • Pearl Ex Pigments
  • Regular white glue (elmers or tacky)
  • Diamond Glaze or Glossy Accents
  • Modge Podge
  • Micro Beads
  • E-6000 and bail (unless you're going to drill your tiles)



Tools Of The Trade:
  • Paintbrush
  • Plastic pallet (for mizing pearl ex pigments)
  • Safety Pin
  • Waterproof, permanent pens - Faver-Castell India Ink pens or Sharpies work well
Process:
  • Step One: Select your stamp. I am using some great small stamps I picked up at Michael's for $1. Ink your stamp.If you are using a stamp larger than the scrabble tile, ink a slightly larger area than you intend to use - it's pretty tough to get the stamp exactly where you want it on the tile. Stamp the image on the tile by laying the tile down on the stamp, not the other way around. Press down lighty, doing your best not to wiggle it around.

  • Step Two: Try layering differnt stamps and different color inks. You can also use embossing powerder and a heat gun at this point if you'd like.

  • Step Three: give the stamped images time to dry. If you are using an  "imitation" scrabble tile, more than likely it has an unfinished surface and the ink will seep into the tile rather quickly. With an actual scrabble tile, the ink will sit on the surface and need more time to dry. Once they are dry, you can add punch to the stamped images using pearl ex pigments, mixed with a little bit of water and glue. Use them just like you would paint- mix colors, play around. I suggest using a small brush to apply the pigment to your tiles.

  • Step Four: Again, allow everything to dry. At this point, you can add 3-dimensional stuff to your scrabble tiles. I recommend starting with micro beads because they're small, however, by all means, play around. If you are using micro beads, I would suggest:
    • Coat the side of the scrabble tile you're working on with a thin layer of mod podge or slightly watered down glue.

    • Place the micro beads about where you want them - it's going to be impossible to play them exactly in the right place on the first try. Using a pin, push the beads to where you want them to be. Allow the mod podge or glue to dry completely.

    • TIP: No matter what - DONT leave the container open. I... I guess I really am a clutz, though I wish I could say I was just multi-tasking too much, but of course... I managed to spill them. All over my desk. It was a disaster. Good luck!

  • Step Four: Once you're happy and everything is dry you can seal the tile. Here is the crux. If you've used a waterbased ink, you're going to need to use a sealant that is NOT water based. Otherwise you're going to end up with a blurry mess. Finally add a coat of diamond glaze or glossy accents. If you're working with non-traditional scrabble tiles, you're going to want to coat every side of the tile. Wait for one side to dry completely before working on another side - I've learned this the hard way...

    • Tips for applying Diamond Glaze: Use even pressure, working around the edges, then moving into the middle. If you happen to get a bubble, you're not really going to be able to pop it. Drag it out using a pin.
  • Step Five: Now it's time to complete the pendant. I always allow my scrabble tiles to dry over night - that way there's no risk of mess ups - and as I am clutsy as it is, I don't need to do anything to add to the liklihood of my messing up. Using a small dab of E-6000, attach a bail and voila!
    • Tips for working with E-6000: If you're sensitive to strong smells, make sure you have some ventilation. I'm pretty sure there are warnings for this... In any case, I try to work with small amounts and leave the room if I start to get a headache. I dab a bit of epoxy on a scrap piece of paper and use the tip of a safety pin to dot a tiny bit on the back of the bail - a lot goes a long way. Then I place the bail on the tile, center it, and use another safety pin or a toothpick to carefully swab away any excess epoxy. This takes some practice :) 



C'est Fin!

0 comments: